Packaging: One unit
Connector: Bosch JPT EV1 Minitimer Jetronic
Dimensions:
- Length: 33.6mm - EV 14C (Compact) with top short adapter and bottom short adapter extends to 60.65mm.
- Body Diameter: 16mm
- Nozzle Length: 24mm
O-Ring Sizes:
- Top O-Ring: 14mm Viton
- Bottom O-Ring: 14mm Viton
Coil Resistance: 12 ohms
Injector Spray Pattern: 30 degrees conical
Spray Angle: Straight (0 degrees)
Flow Rate: 670g / 980cc / 980cm3 at 3 bar
Fuel Compatibility: E85 / M100 compatible; other common fuels acceptable due to stainless steel internal components. Warning: If used with methanol, run the injector with normal fuel afterward. Do not leave the injector sitting with methanol.
Measured Static Maximum Flow Rates in Test Environment
- 29 PSI (2 bar): 720cc/min = 69 lb/h
- 43.5 PSI (3 bar): 900cc/min = 86 lb/h
- 58 PSI (4 bar): 1038cc/min = 99 lb/h
- 78.5 PSI (5 bar): 1170cc/min = 111 lb/h
- 88 PSI (6 bar): 1284cc/min = 122 lb/h
- 101.5 PSI (7 bar): 1344cc/min = 128 lb/h
Note: Test conditions versus practical use may vary significantly depending on auxiliary equipment and other technical factors. This provides useful insight into expected injector performance and is essential information for selecting other components of the fuel system such as fuel pumps, fuel pressure regulators, and fuel filters.
Engine Performance Estimates
Turbo Gasoline (10% margin):
- 1 Cylinder: 129hp (129x1)
- 4 Cylinders: 516hp (129x4)
- 5 Cylinders: 645hp (129x5)
- 6 Cylinders: 774hp (129x6)
- 8 Cylinders: 1032hp (129x8)
Turbo Ethanol (10% margin):
- 1 Cylinder: 112hp (112x1)
- 4 Cylinders: 448hp (112x4)
- 5 Cylinders: 560hp (112x5)
- 6 Cylinders: 672hp (112x6)
- 8 Cylinders: 896hp (112x8)
N/A Gasoline (10% margin):
- 1 Cylinder: 168hp (168x1)
- 4 Cylinders: 672hp (168x4)
- 5 Cylinders: 840hp (168x5)
- 6 Cylinders: 1008hp (168x6)
- 8 Cylinders: 1344hp (168x8)
N/A Ethanol (10% margin):
- 1 Cylinder: 140hp (140x1)
- 4 Cylinders: 560hp (140x4)
- 5 Cylinders: 700hp (140x5)
- 6 Cylinders: 840hp (140x6)
- 8 Cylinders: 1120hp (140x8)
Flow Matching
This injector is delivered with factory tolerances unless you choose to opt for flow matching with much tighter tolerances. We recommend that you have them flow matched before delivery if you are not aware that the factory tolerances can vary significantly. You can run them with unmatched tolerances, match them yourself, or adjust for possible flow variations during tuning in the ECU. Flows can vary from the factory.
When you choose to have them matched by us, this is completed using our high-end equipment. Documentation and certification will accompany the injectors when you select this option.
EAN Code: 4047023028419
Stuck? Our experts will get you back on track!
With years of industry experience, we're here to answer your questions.
Contact us
