Name: Bosch 870cc
Packaging: 1x
Specification
- Connector: Bosch JPT EV1 Minitimer Jetronic
- Length: 33.6mm - EV 14C (Compact) Use top short adapter and bottom short adapter to achieve 60.65mm EV 14L (Long)
- Injector Tip: xT 24mm
- O-ring Top: 14mm Viton
- O-ring Bottom: 14mm Viton
- Body Diameter: 16mm
- Coil Resistance: 12 ohm
- Injector Spray Pattern: 30-degree conical
- Spray Angle: Straight (0 degrees)
- Fuel Compatibility: Compatible with E85 / M100 and withstands other common fuels due to stainless steel internal components. Note: If the injector is used with methanol, it should be flushed with regular fuel afterward. The injector should not be left with methanol over time.
Measured Static Maximum Flow in Test Environment
- 29 PSI (2 bar) 672cc / min = 64 lb / h
- 43.5 PSI (3 bar) 864cc / min = 82 lb / h
- 58 PSI (4 bar) 972cc / min = 93 lb / h
- 78.5 PSI (5 bar) 1098cc / min = 105 lb / h
- 88 PSI (6 bar) 1218cc / min = 116 lb / h
- 101.5 PSI (7 bar) 1320cc / min = 126 lb / h
Note that the test environment vs. practical usage may have significant variances depending on surrounding equipment and other technical factors. This information provides a good baseline for what to expect from the injectors and offers foundational guidance when selecting other components in the fuel system such as fuel pumps, fuel pressure regulators, and fuel filters.
Engine Power Turbo
Gasoline 10% Marginal
- 1 Cylinder - 115hp (115x1)
- 4 Cylinders - 460hp (115x4)
- 5 Cylinders - 575hp (115x5)
- 6 Cylinders - 690hp (115x6)
- 8 Cylinders - 920hp (115x8)
Ethanol 10% Marginal
- 1 Cylinder - 99hp (99x1)
- 4 Cylinders - 396hp (99x4)
- 5 Cylinders - 495hp (99x5)
- 6 Cylinders - 594hp (99x6)
- 8 Cylinders - 792hp (99x8)
Engine Power N/A
Gasoline 10% Marginal
- 1 Cylinder - 149hp (149x1)
- 4 Cylinders - 596hp (149x4)
- 5 Cylinders - 745hp (149x5)
- 6 Cylinders - 894hp (149x6)
- 8 Cylinders - 1192hp (149x8)
Ethanol 10% Marginal
- 1 Cylinder - 124hp (124x1)
- 4 Cylinders - 496hp (124x4)
- 5 Cylinders - 620hp (124x5)
- 6 Cylinders - 744hp (124x6)
- 8 Cylinders - 992hp (124x8)
Flow Matching
These injectors are supplied directly with factory tolerances unless you opt for us to flow match them with significantly tighter tolerances than factory. We always recommend choosing to have them flow matched with us before delivery unless you are familiar with the variability of factory tolerances. You can run them un-matched with larger tolerances, match the injectors yourself, or compensate for the potential variances in flow when tuning in the control system. The extent of variation from factory can always differ.
If you choose for us to match the injectors, this will be performed with our top-tier equipment! Documentation and certification from us will accompany the injectors when this option is selected.
Stuck? Our experts will get you back on track!
With years of industry experience, we're here to answer your questions.
Contact us
